git ignore

.gitignore

@@ -0,0 +1 @@
+**/.DS_Store

boot/config.txt

@@ -0,0 +1,117 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+#overscan_left=16
+#overscan_right=16
+#overscan_top=16
+#overscan_bottom=16
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2c_arm=on
+#dtparam=i2s=on
+dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+
+####################################################
+####     MainsailOS specific configurations     ####
+####################################################
+####      DO NOT CHANGE SECTION BELOW !!!       ####
+####   UNLESS YOU KNOW WHAT YOU ARE DOING !!!   ####
+####################################################
+
+## For more options and information see
+## https://www.raspberrypi.com/documentation/computers/config_txt.html
+## Some settings may impact device functionality. See link above for details
+
+## For additional information about device filters see
+## https://www.raspberrypi.com/documentation/computers/config_txt.html#model-filters
+
+
+[pi0]
+## This affects Pi Zero(W) and Pi Zero2
+## Due lag of RAM, limit GPU RAM
+gpu_mem=128
+
+[pi2]
+gpu_mem=256
+
+[pi3]
+## Use 256 if 1Gb Ram Model!
+gpu_mem=128
+# gpu_mem=256
+
+[pi4]
+## Enable DRM VC4 V3D driver on top of the dispmanx display stack
+dtoverlay=vc4-fkms-v3d
+max_framebuffers=2
+## Do not use more than 256Mb on Pi Model 4, it uses its own Management.
+gpu_mem=256
+
+[all]
+
+## SPI Interface is enabled by default for Input Shaper
+## To revert that comment out line #48
+## This colides with Hyperpixel Display!
+## Hyperpixel Screen uses the same Pin for Backlight.
+
+## Enable Hardware UART for Serial Communication
+enable_uart=1
+dtoverlay=disable-bt
+
+## Enable VideoCore at boot, needed for Raspicams and DSI devices.
+start_x=1
+
+### EXPERIMENTAL - Enable 64bit Kernel
+### The 64-bit kernel will only work on:
+### Raspberry Pi 3, 3+, 4, 400, Zero 2 W and 2B rev 1.2
+### and Raspberry Pi Compute Modules 3, 3+ and 4.
+# arm_64bit=1
+
+dtoverlay=dwc2,dr_mode=host
+
+####################################################

printer.cfg

@@ -77,11 +77,15 @@ homing_speed: 40
 [fan]
 pin: PD2
 
+[led WhiteLeds]
+white_pin: PD4
+initial_WHITE: 0.7
+
 #[heater_fan fan1]
 #pin: PD3
 
 #[heater_fan fan2]
-#pin: PD4
+
 
 #[bltouch]
 #sensor_pin: PC14