118 lines
3.2 KiB
Plaintext
Executable File
118 lines
3.2 KiB
Plaintext
Executable File
# For more options and information see
|
|
# http://rpf.io/configtxt
|
|
# Some settings may impact device functionality. See link above for details
|
|
|
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# uncomment this if your display has a black border of unused pixels visible
|
|
# and your display can output without overscan
|
|
#disable_overscan=1
|
|
|
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
#overscan_left=16
|
|
#overscan_right=16
|
|
#overscan_top=16
|
|
#overscan_bottom=16
|
|
|
|
# uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# uncomment if hdmi display is not detected and composite is being output
|
|
#hdmi_force_hotplug=1
|
|
|
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
|
#hdmi_group=1
|
|
#hdmi_mode=1
|
|
|
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
#uncomment to overclock the arm. 700 MHz is the default.
|
|
#arm_freq=800
|
|
|
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
#dtparam=i2c_arm=on
|
|
#dtparam=i2s=on
|
|
dtparam=spi=on
|
|
|
|
# Uncomment this to enable infrared communication.
|
|
#dtoverlay=gpio-ir,gpio_pin=17
|
|
#dtoverlay=gpio-ir-tx,gpio_pin=18
|
|
|
|
# Additional overlays and parameters are documented /boot/overlays/README
|
|
|
|
# Enable audio (loads snd_bcm2835)
|
|
dtparam=audio=on
|
|
|
|
|
|
####################################################
|
|
#### MainsailOS specific configurations ####
|
|
####################################################
|
|
#### DO NOT CHANGE SECTION BELOW !!! ####
|
|
#### UNLESS YOU KNOW WHAT YOU ARE DOING !!! ####
|
|
####################################################
|
|
|
|
## For more options and information see
|
|
## https://www.raspberrypi.com/documentation/computers/config_txt.html
|
|
## Some settings may impact device functionality. See link above for details
|
|
|
|
## For additional information about device filters see
|
|
## https://www.raspberrypi.com/documentation/computers/config_txt.html#model-filters
|
|
|
|
|
|
[pi0]
|
|
## This affects Pi Zero(W) and Pi Zero2
|
|
## Due lag of RAM, limit GPU RAM
|
|
gpu_mem=128
|
|
|
|
[pi2]
|
|
gpu_mem=256
|
|
|
|
[pi3]
|
|
## Use 256 if 1Gb Ram Model!
|
|
gpu_mem=128
|
|
# gpu_mem=256
|
|
|
|
[pi4]
|
|
## Enable DRM VC4 V3D driver on top of the dispmanx display stack
|
|
dtoverlay=vc4-fkms-v3d
|
|
max_framebuffers=2
|
|
## Do not use more than 256Mb on Pi Model 4, it uses its own Management.
|
|
gpu_mem=256
|
|
|
|
[all]
|
|
|
|
## SPI Interface is enabled by default for Input Shaper
|
|
## To revert that comment out line #48
|
|
## This colides with Hyperpixel Display!
|
|
## Hyperpixel Screen uses the same Pin for Backlight.
|
|
|
|
## Enable Hardware UART for Serial Communication
|
|
enable_uart=1
|
|
dtoverlay=disable-bt
|
|
|
|
## Enable VideoCore at boot, needed for Raspicams and DSI devices.
|
|
start_x=1
|
|
|
|
### EXPERIMENTAL - Enable 64bit Kernel
|
|
### The 64-bit kernel will only work on:
|
|
### Raspberry Pi 3, 3+, 4, 400, Zero 2 W and 2B rev 1.2
|
|
### and Raspberry Pi Compute Modules 3, 3+ and 4.
|
|
# arm_64bit=1
|
|
|
|
dtoverlay=dwc2,dr_mode=host
|
|
|
|
####################################################
|