toolhead

printer.cfg

@@ -6,62 +6,48 @@
 
 [include mainsail.cfg]
 
+[mcu EBBCan]
+  canbus_uuid: 82edf63bd1a9
+
+[include toolhead.cfg]
+
 [stepper_x]
-step_pin: PC6
-dir_pin: !PA14
-enable_pin: !PC7
-microsteps: 16
-rotation_distance: 40
-endstop_pin: ^!PC0
-position_endstop: 0
-position_max: 230
-homing_speed: 80
+  step_pin: PC6
+  dir_pin: !PA14
+  enable_pin: !PC7
+  microsteps: 16
+  rotation_distance: 40
+  endstop_pin: ^!PC0
+  position_endstop: 0
+  position_max: 230
+  homing_speed: 80
 
 [stepper_y]
-step_pin: PB10
-dir_pin: PB2
-enable_pin: !PB11
-microsteps: 16
-rotation_distance: 40
-endstop_pin: ^!PC1
-position_endstop: 230
-position_max: 230
-homing_speed: 80
+  step_pin: PB10
+  dir_pin: PB2
+  enable_pin: !PB11
+  microsteps: 16
+  rotation_distance: 40
+  endstop_pin: ^!PC1
+  position_endstop: 230
+  position_max: 230
+  homing_speed: 80
 
 [stepper_z]
-step_pin: PB0
-dir_pin: !PC5
-enable_pin: !PB1
-microsteps: 16
-rotation_distance: 8
-endstop_pin: ^!PC2
-position_endstop: 207.890
-position_max: 232
-position_min: -10
-homing_speed: 40
-#second_homing_speed: 3
-#homing_retract_dist: 3
+  step_pin: PB0
+  dir_pin: !PC5
+  enable_pin: !PB1
+  microsteps: 16
+  rotation_distance: 8
+  endstop_pin: ^!PC2
+  position_endstop: 207.890
+  position_max: 232
+  position_min: -10
+  homing_speed: 40
 
-# [extruder]
-# step_pin: PB3
-# dir_pin: PB4
-# enable_pin: !PD5
-# microsteps: 16
-# rotation_distance: 22.9
-# nozzle_diameter: 0.400
-# filament_diameter: 1.750
-# heater_pin: PC8
-# sensor_type: Generic 3950
-# sensor_pin: PA0
-# control: pid
-# pid_Kp: 20.837
-# pid_Ki: 1.037
-# pid_Kd: 104.708
-# min_temp: 0
-# max_temp: 275
 
-#[filament_switch_sensor extruder_filament_sensor]
-#switch_pin: ^!PC15
+[filament_switch_sensor extruder_filament_sensor]
+  switch_pin: ^!PC15
 
 # [heater_bed]
 #   heater_pin: PD8

toolhead.cfg

@@ -0,0 +1,43 @@
+# This file contains common pin mappings for the BIGTREETECH EBBCan
+# Canbus board. To use this config, the firmware should be compiled for the
+# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
+# The "EBB Can" micro-controller will be used to control the components on the nozzle.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+# [mcu EBBCan]
+# canbus_uuid: 82edf63bd1a9
+
+[adxl345]
+  cs_pin: EBBCan: PB12
+  spi_software_sclk_pin: EBBCan: PB10
+  spi_software_mosi_pin: EBBCan: PB11
+  spi_software_miso_pin: EBBCan: PB2
+  axes_map: x,y,z
+
+[fan]
+ pin: EBBCan: PA0
+
+[heater_fan hotend_fan]
+ pin: EBBCan: PA1
+ heater: extruder
+ heater_temp: 50.0
+
+[bltouch]
+  sensor_pin: ^EBBCan:PB8
+  control_pin: EBBCan:PB9
+  z_offset: 1.230
+
+# [tmc2209 extruder]
+# uart_pin: EBBCan: PA15
+# run_current: 0.650
+# stealthchop_threshold: 999999
+
+#[neopixel hotend_rgb]
+#pin: EBBCan:PD3
+
+#[filament_switch_sensor switch_sensor]
+#switch_pin: EBBCan:PB4
+
+#[filament_motion_sensor motion_sensor]
+#switch_pin: ^EBBCan:PB3