added extruder and bed

printer.cfg

@@ -4,7 +4,16 @@
 
 # See docs/Config_Reference.md for a description of parameters.
 
-[include mainsail.cfg]
+[printer]
+kinematics: cartesian
+max_velocity: 180
+max_accel: 3000
+max_z_velocity: 100
+max_z_accel: 100
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_hurakan-if00
+
 
 [mcu EBBCan]
   canbus_uuid: 82edf63bd1a9
@@ -67,51 +76,28 @@ pin: PD2
 white_pin: PD4
 initial_WHITE: 0.7
 
-#[heater_fan fan1]
-#pin: PD3
-
-#[heater_fan fan2]
 
 
-#[bltouch]
-#sensor_pin: PC14
-#control_pin: PA1
 
-#[adxl345]
-#cs_pin: PD9
-#spi_bus: spi1
-#axes_map: z,y,-x
+##############################
+#        bed leveling        #
+##############################
 
-#[neopixel rgb1]
-#pin: PD0
+[bed_screws]
+  screw1: 120, 185
+  screw1_name: "rear mid screw"
+  screw2: 20 ,20
+  screw2_name: "front left screw"
+  screw3: 220, 20
+  screw3_name: "front right screw"
+  horizontal_move_z: 5
 
-#[neopixel rgb2]
-#pin: PD1
-
-[mcu]
-serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_hurakan-if00
-
-[printer]
-kinematics: cartesian
-max_velocity: 180
-max_accel: 3000
-max_z_velocity: 100
-max_z_accel: 100
-
-########################################
-# EXP1 / EXP2 (display) pins
-########################################
-
-[board_pins]
-aliases:
-    # EXP1 header
-    EXP1_1=PD6,  EXP1_3=PB9,  EXP1_5=PA15, EXP1_7=PA9,   EXP1_9=<GND>,
-    EXP1_2=PB8,  EXP1_4=PC3,  EXP1_6=PA10, EXP1_8=PB5,   EXP1_10=<5V>,
-    # EXP2 header
-    EXP2_1=PB14, EXP2_3=PC11, EXP2_5=PC12, EXP2_7=PC13,  EXP2_9=<GND>,
-    EXP2_2=PB13, EXP2_4=PA8,  EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
-
-# See the sample-lcd.cfg file for definitions of common LCD displays.
+[bed_mesh]
+  speed: 120
+  horizontal_move_z: 5
+  mesh_min: 15, 50
+  mesh_max: 190, 200
+  probe_count: 3, 3
 
 ########################################
 # TMC2209 configuration
@@ -120,19 +106,62 @@ aliases:
 [tmc2209 stepper_x]
 uart_pin: PB12
 run_current: 0.800
-#diag_pin:
 
 [tmc2209 stepper_y]
 uart_pin: PC10
 run_current: 0.800
-#diag_pin:
 
 [tmc2209 stepper_z]
 uart_pin: PC9
 run_current: 0.800
-#diag_pin:
 
-# [tmc2209 extruder]
-# uart_pin: PA13
-# run_current: 0.600
-#diag_pin:
+
+
+[extruder]
+  step_pin: PL7
+  dir_pin: !PL6
+  enable_pin: !PC0
+  microsteps: 16
+  rotation_distance: 10.07
+  nozzle_diameter: 0.400
+  filament_diameter: 1.74
+  heater_pin: EBBCan: PB13
+  control: pid
+  pid_Kp: 21.527
+  pid_Ki: 1.063
+  pid_Kd: 108.982
+  min_temp: 0 
+  max_temp: 270
+  sensor_type:MAX31865
+  sensor_pin: EBBCan: PA4
+  spi_bus: spi1
+  rtd_nominal_r: 100
+  rtd_reference_r: 430
+  rtd_num_of_wires: 2
+  pressure_advance: 0.78
+
+
+  [include mainsail.cfg]
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*#
+#*# [extruder]
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.725000, 0.715000, 0.660000, 0.610000, 0.570000
+#*# 	  0.660000, 0.650000, 0.600000, 0.575000, 0.485000
+#*# 	  0.695000, 0.650000, 0.605000, 0.585000, 0.495000
+#*# x_count = 5
+#*# y_count = 3
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = lagrange
+#*# tension = 0.2
+#*# min_x = 15.0
+#*# max_x = 190.0
+#*# min_y = 50.0
+#*# max_y = 200.0