From a6e4c1e3085034cb3d2b0a657e35596a8b08e322 Mon Sep 17 00:00:00 2001
From: willem <willem@oldemans.nl>
Date: Thu, 17 Nov 2022 20:53:55 +0100
Subject: [PATCH] added fan +bed level

---
 UM2_v2.1.cfg                    |  4 +-
 bigtreetech-ebb-canbus-v1.2.cfg |  4 +-
 moonraker.conf                  |  2 +-
 printer-20221117_192818.cfg     | 77 +++++++++++++++++++++++++++++++++
 printer.cfg                     | 25 ++++++++++-
 5 files changed, 106 insertions(+), 6 deletions(-)
 create mode 100644 printer-20221117_192818.cfg

diff --git a/UM2_v2.1.cfg b/UM2_v2.1.cfg
index 6b1c5f4..cc09ff9 100644
--- a/UM2_v2.1.cfg
+++ b/UM2_v2.1.cfg
@@ -13,8 +13,8 @@ max_temp: 110
 [verify_heater heater_bed]
 check_gain_time: 80
 
-[fan]
-pin: PH4
+#[fan]
+#pin: PH4
 
 #[heater_fan Heater_fan]
 #pin: PJ6
diff --git a/bigtreetech-ebb-canbus-v1.2.cfg b/bigtreetech-ebb-canbus-v1.2.cfg
index 9ed7209..7f6ebfd 100644
--- a/bigtreetech-ebb-canbus-v1.2.cfg
+++ b/bigtreetech-ebb-canbus-v1.2.cfg
@@ -47,8 +47,8 @@ rtd_num_of_wires: 2
 # run_current: 0.650
 # stealthchop_threshold: 999999
 
-# [fan]
-# pin: EBBCan: PA0
+[fan]
+ pin: EBBCan: PA0
 
 [heater_fan hotend_fan]
  pin: EBBCan: PA1
diff --git a/moonraker.conf b/moonraker.conf
index 6ecbdcd..09cf6bd 100644
--- a/moonraker.conf
+++ b/moonraker.conf
@@ -6,7 +6,7 @@ port: 7125
 max_upload_size: 1024
 
 [file_manager]
-config_path: ~/klipper_config
+#config_path: ~/klipper_config
 #log_path: ~/klipper_logs
 # post processing for object cancel. Not recommended for low resource SBCs such as a Pi Zero. Default False
 enable_object_processing: False
diff --git a/printer-20221117_192818.cfg b/printer-20221117_192818.cfg
new file mode 100644
index 0000000..85b6cd5
--- /dev/null
+++ b/printer-20221117_192818.cfg
@@ -0,0 +1,77 @@
+# This file contains common pin mappings for Ultimaker UltiMainboard v2
+# boards. To use this config, the firmware should be compiled for the
+# AVR atmega2560.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[include macros.cfg]
+
+[mcu]
+serial: /dev/serial/by-id/usb-Arduino__www.arduino.cc__0042_8543034383735181D1B1-if00
+
+[include UM2_v2.1.cfg]
+[include bigtreetech-ebb-canbus-v1.2.cfg]
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 3000
+max_z_velocity: 25
+max_z_accel: 30
+
+
+# [safe_z_home]
+# home_xy_position: 100, 100 # Change coordinates to the center of your print bed
+# speed: 50
+# z_hop: 10                 # Move up 10mm
+# z_hop_speed: 5
+
+[bed_screws]
+screw1: 120, 185
+screw1_name: "rear mid screw"
+screw2: 20 ,20
+screw2_name: "front left screw"
+screw3: 220, 20
+screw3_name: "front right screw"
+horizontal_move_z: 5
+
+[bed_mesh]
+speed: 120
+horizontal_move_z: 5
+mesh_min: 15, 50
+mesh_max: 190, 200
+probe_count: 5, 3
+
+[filament_motion_sensor runout]
+#   The minimum length of filament pulled through the sensor to trigger
+#   a state change on the switch_pin
+#   Default is 7 mm.
+detection_length: 14.0
+extruder: extruder
+pause_on_runout: FALSE
+runout_gcode:
+  {action_respond_info("RUNOUT: Filament runout")}
+  PAUSE
+insert_gcode: {action_respond_info("RUNOUT: Filament inserted")}
+#   The minimum amount of time in seconds to delay between events.
+#   Events triggered during this time period will be silently
+#   ignored. The default is 3 seconds.
+#event_delay: 3.0
+#   The amount of time to delay, in seconds, between the pause command
+#   dispatch and execution of the runout_gcode. It may be useful to
+#   increase this delay if OctoPrint exhibits strange pause behavior.
+#   Default is 0.5 seconds.
+#pause_delay: 0.5
+##    XYE mcu E0DET
+switch_pin: ^!PB7
+
+
+[include mainsail.cfg]
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [stepper_z]
+#*# position_endstop = 207.280
+#*#
+#*# [extruder]
diff --git a/printer.cfg b/printer.cfg
index ef6d9d9..52027b1 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -10,6 +10,7 @@
 serial: /dev/serial/by-id/usb-Arduino__www.arduino.cc__0042_8543034383735181D1B1-if00
 
 [include UM2_v2.1.cfg]
+[include bigtreetech-ebb-canbus-v1.2.cfg]
 
 [printer]
 kinematics: cartesian
@@ -34,7 +35,12 @@ screw3: 220, 20
 screw3_name: "front right screw"
 horizontal_move_z: 5
 
-[include bigtreetech-ebb-canbus-v1.2.cfg]
+[bed_mesh]
+speed: 120
+horizontal_move_z: 5
+mesh_min: 15, 50
+mesh_max: 190, 200
+probe_count: 5, 3
 
 [filament_motion_sensor runout]
 #   The minimum length of filament pulled through the sensor to trigger
@@ -69,3 +75,20 @@ switch_pin: ^!PB7
 #*# position_endstop = 207.280
 #*#
 #*# [extruder]
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.725000, 0.715000, 0.660000, 0.610000, 0.570000
+#*# 	  0.660000, 0.650000, 0.600000, 0.575000, 0.485000
+#*# 	  0.695000, 0.650000, 0.605000, 0.585000, 0.495000
+#*# x_count = 5
+#*# y_count = 3
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = lagrange
+#*# tension = 0.2
+#*# min_x = 15.0
+#*# max_x = 190.0
+#*# min_y = 50.0
+#*# max_y = 200.0