substitutions:
  device_name: "t-embed"
  friendly_name: "t-embed"
  comment: "esp32-s3, lcd, rotary, leds, mic, spk"
  location: "zolder"
  api_password: !secret t-embed_api
  ota_password: !secret ota_password
  wifi_ssid: !secret wifi_ssid
  wifi_password: !secret wifi_password
  gateway: !secret ip_gateway
  subnet: !secret ip_subnet
  ip: !secret t-embed_ip
  update_interval: 30s
  num_leds: "7"
  led_chipset: APA102

  #t-embed pins

  pin_i2slrclk: GPIO05
  pin_i2sbclk: GPIO07
  pin_i2sdout: GPIO06
  pin_es7210_blck: GPIO47
  pin_es7210_lrck: GPIO21
  pin_es7210_din: GPIO14
  pin_es7210_mclk: GPIO48
  pin_sd_cs: GPIO39
  pin_sd_sck: GPIO40
  pin_sd_mosi: GPIO41
  pin_sd_miso: GPIO38
  pin_power: GPIO46
  pin_led_data: GPIO42
  pin_led_clk: GPIO45
  pin_encode_a: GPIO02
  pin_encode_b: GPIO01
  pin_encode_btn: GPIO00
  pin_sda: GPIO44
  pin_scl: GPIO43
  pin_lcd_bl: GPIO15
  pin_lcd_dc: GPIO13
  pin_lcd_cs: GPIO10
  pin_lcd_clk: GPIO12
  pin_lcd_mosi: GPIO11
  pin_lcd_res: GPIO09
  pin_vbat: GPIO4


packages:
  board: !include boards/esp32-s3-voice.yaml
  spkmic: !include interfaces/SpkMicVoiceTembed.yaml
  #leds: !include templates/light_fastled_spi.yaml
  connection: !include common/wifi.yaml
  logger: !include templates/logger.yaml
  backlight: !include templates/backlight.yaml
  #i2c: !include interfaces/i2c_a.yaml
  #lightsens: !include sensors/light_tsl2591.yaml
  encoder: !include sensors/encoder.yaml

esphome:
  name: ${device_name}
  platformio_options:
    # build_flags: |-
    #   -DARDUINO_USB_CDC_ON_BOOT=1 -DLV_CONF_INCLUDE_SIMPLE
    board_build.mcu: esp32s3
    board_build.name: "LilyGO T-Embed ESP32-S3"
    board_build.upload.flash_size: "16MB"
    board_build.upload.maximum_size: 16777216
    board_build.vendor: "LilyGO"
  on_boot:
    priority: 800
    then:
      # - lambda: |-
      #     id(disp).enable();
      #     id(disp).transfer_byte(0x11);
      #     id(disp).disable();
      - switch.turn_on: power_on

button:
  - platform: restart
    name: 'Restart'

api:
  on_client_connected:
        then:
          - delay: 50ms
          - micro_wake_word.start:
  on_client_disconnected:
        then:
          - voice_assistant.stop: 

switch:
  - platform: template
    id: mute
    name: mute
    optimistic: true
    on_turn_on: 
      - micro_wake_word.stop:
      - voice_assistant.stop:
    on_turn_off:
      - micro_wake_word.start:
  - platform: gpio
    pin:
      number: ${pin_power}
      mode:
        output: True
    restore_mode: RESTORE_DEFAULT_ON
    name: "Power On"
    id: power_on


# time:
#   - platform: homeassistant
#     id: home_time

voice_assistant:
  id: va
  microphone: mic
  noise_suppression_level: 2.0
  volume_multiplier: 4.0
  on_error:
          - micro_wake_word.start:  
  on_end:
        then:
          - wait_until:
              not:
                voice_assistant.is_running:
          - micro_wake_word.start:  


micro_wake_word:
  on_wake_word_detected:
    - voice_assistant.start:
  model: okay_nabu


spi:
  id: ledbus
  mosi_pin: ${pin_led_data}
  clk_pin: ${pin_led_clk}

light:
  - platform: spi_led_strip
    num_leds: 30
    spi_id: "ledbus"
    color_correct: [80%, 60%, 100%]
    id: rgb_led
    name: "RGB LED Strip"
    data_rate: 1MHz

# font:
#   - file: "gfonts://Roboto"
#     id: roboto
#     size: 96

# spi:
#   - id: spi_display
#     clk_pin: ${pin_lcd_clk}
#     mosi_pin: ${pin_lcd_mosi}

# display:
#   - platform: st7789v
#     model: CUSTOM
#     eightbitcolor: False
#     rotation: 270
#     width: 170
#     height: 320
#     offset_width: 0
#     offset_height: 35
#     #backlight_pin: ${pin_lcd_bl}
#     cs_pin: ${pin_lcd_cs}
#     dc_pin: ${pin_lcd_dc}
#     reset_pin: ${pin_lcd_res}
#     update_interval: 5s
#     id: disp
#     lambda: |-
#       it.strftime(10, 20, id(roboto), "%H:%M", id(home_time).now());